I've got a problem with my wireless router, networking tech is not my strong suite so I'm asking for help here:

For some odd, odd reason, 2 of three of my Kubuntu machines have their wireless cut off. I've got no idea at all what's causing this.

The two affected machines are quite far away from the router, the third is quite close to it.

I authenticate with the wireless router...then for some odd reason, my connection dies...Kubuntu, however (and a few other distros I've tried) all report that I still HAVE a connection...yet I cannot access webpages, or even the router itself.

The routers logs never show me disconnecting, and one of my computers has the GNOME network manager on it (which still does it) and the other did have the WICD client on it (which did it far more often)

Interestingly enough, if I replace the network client, then no such problems occur...until I reset either machine. :/ Two machines are now using the KNetworkManager frontend

So, am I just looking at a case of poor signal strength? or something else? How on earth do I correct it?

Try checking the output of "iwconfig" and "dmesg" once you are disconnected.

dante@dante-laptop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11bgn ESSID:"ashton"
Mode:Managed Frequency:2.432 GHz Access Point: 00:1D:73:B3:60:38
Bit Rate=0 kb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=21/70 Signal level=-89 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

vboxnet0 no wireless extensions.


suddenly doing that seems to of restored my connection...I'll do the other when it screws up again.

Recently tried out distro based on older kernel, wireless did not die...how odd...

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-20-generic (buildd@palmer) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC 2010 (Ubuntu 2.6.31-20.58-generic)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000aff98000 (usable)
[ 0.000000] BIOS-e820: 00000000aff98000 - 00000000affa0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000affa0000 - 00000000affae000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000affae000 - 00000000afff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000afff0000 - 00000000c0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.5 present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xaff98 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable)
[ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000aff98000 (usable)
[ 0.000000] modified: 00000000aff98000 - 00000000affa0000 (ACPI NVS)
[ 0.000000] modified: 00000000affa0000 - 00000000affae000 (ACPI data)
[ 0.000000] modified: 00000000affae000 - 00000000afff0000 (ACPI NVS)
[ 0.000000] modified: 00000000afff0000 - 00000000c0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000ff700000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] Using x86 segment limits to approximate NX protection
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 10000-15000
[ 0.000000] RAMDISK: 378a3000 - 37fef94b
[ 0.000000] Allocated new RAMDISK: 008b2000 - 00ffe94b
[ 0.000000] Move RAMDISK from 00000000378a3000 - 0000000037fef94a to 008b2000 - 00ffe94a
[ 0.000000] ACPI: RSDP 000fa260 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT affa0100 00084 (v01 _ASUS_ Notebook 20080908 MSFT 00000097)
[ 0.000000] ACPI: FACP affa0290 000F4 (v03 090808 FACP1031 20080908 MSFT 00000097)
[ 0.000000] ACPI: DSDT affa06e0 0D59B (v01 F5GL0 F5GL0207 00000207 INTL 20051117)
[ 0.000000] ACPI: FACS affae000 00040
[ 0.000000] ACPI: APIC affa0390 00070 (v01 090808 APIC1031 20080908 MSFT 00000097)
[ 0.000000] ACPI: MCFG affa0440 0003C (v01 090808 OEMMCFG 20080908 MSFT 00000097)
[ 0.000000] ACPI: SLIC affa0480 00176 (v01 _ASUS_ Notebook 20080908 MSFT 00000097)
[ 0.000000] ACPI: WDRT affa0600 00047 (v01 090808 NV-WDRT 20080908 MSFT 00000097)
[ 0.000000] ACPI: ECDT affa0680 00053 (v01 090808 OEMECDT 20080908 MSFT 00000097)
[ 0.000000] ACPI: DBGP affa0400 00034 (v01 090808 DBGP1031 20080908 MSFT 00000097)
[ 0.000000] ACPI: BOOT affa0650 00028 (v01 090808 BOOT1031 20080908 MSFT 00000097)
[ 0.000000] ACPI: OEMB affae040 00072 (v01 090808 OEMB1031 20080908 MSFT 00000097)
[ 0.000000] ACPI: HPET affadc80 00038 (v01 090808 OEMHPET0 20080908 MSFT 00000097)
[ 0.000000] ACPI: NVHD affae0c0 00284 (v01 090808 NVHDCP 20080908 MSFT 00000097)
[ 0.000000] ACPI: SSDT affaf070 004F0 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1927MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] node 0 low ram: 00000000 - 377fe000
[ 0.000000] node 0 bootmap 00011000 - 00017f00
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00008ad060] TEXT DATA BSS ==> [0000100000 - 00008ad060]
[ 0.000000] #4 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000]
[ 0.000000] #5 [00008ae000 - 00008b11de] BRK ==> [00008ae000 - 00008b11de]
[ 0.000000] #6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
[ 0.000000] #7 [00008b2000 - 0000ffe94b] NEW RAMDISK ==> [00008b2000 - 0000ffe94b]
[ 0.000000] #8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x000aff98
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x000aff98
[ 0.000000] On node 0 totalpages: 720678
[ 0.000000] free_area_init_node: node 0, pgdat c0788900, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3950 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 3856 pages used for memmap
[ 0.000000] HighMem zone: 489610 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages at c260a000, static data 35612 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 715046
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-20-generic root=UUID=1d3e647f-c65b-41fc-bbbe-5094cfe7b4fc ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 14415520 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:000aff98)
[ 0.000000] Memory: 2828928k/2883168k available (4578k kernel code, 52928k reserved, 2146k data, 540k init, 1973864k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff1d000 - 0xfffff000 ( 904 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc0792000 - 0xc0819000 ( 540 kB)
[ 0.000000] .data : 0xc0578948 - 0xc0791408 (2146 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0578948 (4578 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:424
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2000.222 MHz processor.
[ 0.000016] spurious 8259A interrupt: IRQ7.
[ 0.001968] Console: colour VGA+ 80x25
[ 0.001972] console [tty0] enabled
[ 0.002147] hpet clockevent registered
[ 0.002152] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.002159] Calibrating delay loop (skipped), value calculated using timer frequency.. 4000.44 BogoMIPS (lpj=8000888)
[ 0.002181] Security Framework initialized
[ 0.002205] AppArmor: AppArmor initialized
[ 0.002212] Mount-cache hash table entries: 512
[ 0.002361] Initializing cgroup subsys ns
[ 0.002367] Initializing cgroup subsys cpuacct
[ 0.002372] Initializing cgroup subsys memory
[ 0.002378] Initializing cgroup subsys freezer
[ 0.002381] Initializing cgroup subsys net_cls
[ 0.002397] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.002400] CPU: L2 cache: 1024K
[ 0.002403] CPU: Physical Processor ID: 0
[ 0.002405] CPU: Processor Core ID: 0
[ 0.002409] mce: CPU supports 6 MCE banks
[ 0.002418] CPU0: Thermal monitoring enabled (TM2)
[ 0.002421] using mwait in idle threads.
[ 0.002429] Performance Counters: Core2 events, Intel PMU driver.
[ 0.002439] ... version: 2
[ 0.002440] ... bit width: 40
[ 0.002442] ... generic counters: 2
[ 0.002444] ... value mask: 000000ffffffffff
[ 0.002446] ... max period: 000000007fffffff
[ 0.002448] ... fixed-purpose counters: 3
[ 0.002449] ... counter mask: 0000000700000003
[ 0.002454] Checking 'hlt' instruction... OK.
[ 0.018761] ACPI: Core revision 20090521
[ 0.048468] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.089651] CPU0: Intel(R) Pentium(R) Dual CPU T3200 @ 2.00GHz stepping 0d
[ 0.092001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 3999.99 BogoMIPS (lpj=7999986)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 1024K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] mce: CPU supports 6 MCE banks
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.177768] CPU1: Intel(R) Pentium(R) Dual CPU T3200 @ 2.00GHz stepping 0d
[ 0.177786] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.180029] Brought up 2 CPUs
[ 0.180032] Total of 2 processors activated (8000.43 BogoMIPS).
[ 0.180099] CPU0 attaching sched-domain:
[ 0.180102] domain 0: span 0-1 level MC
[ 0.180105] groups: 0 1
[ 0.180111] CPU1 attaching sched-domain:
[ 0.180113] domain 0: span 0-1 level MC
[ 0.180116] groups: 1 0
[ 0.180203] Booting paravirtualized kernel on bare hardware
[ 0.180222] regulator: core version 0.5
[ 0.180222] Time: 18:43:07 Date: 04/25/10
[ 0.180222] NET: Registered protocol family 16
[ 0.180258] EISA bus registered
[ 0.180270] ACPI: bus type pci registered
[ 0.180355] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 31
[ 0.180358] PCI: Not using MMCONFIG.
[ 0.180624] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=8
[ 0.180626] PCI: Using configuration type 1 for base access
[ 0.184107] bio: create slab <bio-0> at 0
[ 0.185975] ACPI: EC: EC description table is found, configuring boot EC
[ 0.185988] ACPI: EC: Look up EC in DSDT
[ 0.187526] ACPI: EC: ASUSTek keeps feeding us with broken ECDT tables, which are very hard to workaround. Trying to use DSDT EC info instead. Please send output of acpidump to linux-acpi@vger.kernel.org
[ 0.205411] ACPI: Interpreter enabled
[ 0.205421] ACPI: (supports S0 S3 S4 S5)
[ 0.205448] ACPI: Using IOAPIC for interrupt routing
[ 0.205528] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 31
[ 0.214642] PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
[ 0.214645] PCI: Using MMCONFIG for extended config space
[ 0.234756] ACPI: EC: GPE = 0x27, I/O: command/status = 0x66, data = 0x62
[ 0.234759] ACPI: EC: driver started in poll mode
[ 0.235359] ACPI: No dock devices found.
[ 0.235956] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.236233] pci 0000:00:03.0: reg 10 io port: [0x4f00-0x4fff]
[ 0.236354] pci 0000:00:03.2: reg 10 io port: [0x4900-0x493f]
[ 0.236371] pci 0000:00:03.2: reg 20 io port: [0x4d00-0x4d3f]
[ 0.236377] pci 0000:00:03.2: reg 24 io port: [0x4e00-0x4e3f]
[ 0.236404] pci 0000:00:03.2: PME# supported from D3hot D3cold
[ 0.236410] pci 0000:00:03.2: PME# disabled
[ 0.236595] pci 0000:00:03.5: reg 10 32bit mmio: [0xfce80000-0xfcefffff]
[ 0.236698] pci 0000:00:04.0: reg 10 32bit mmio: [0xfce7f000-0xfce7ffff]
[ 0.236736] pci 0000:00:04.0: supports D1 D2
[ 0.236739] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.236743] pci 0000:00:04.0: PME# disabled
[ 0.236778] pci 0000:00:04.1: reg 10 32bit mmio: [0xfce7ec00-0xfce7ecff]
[ 0.236823] pci 0000:00:04.1: supports D1 D2
[ 0.236825] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.236829] pci 0000:00:04.1: PME# disabled
[ 0.236872] pci 0000:00:08.0: reg 10 32bit mmio: [0xfce78000-0xfce7bfff]
[ 0.236911] pci 0000:00:08.0: PME# supported from D3hot D3cold
[ 0.236915] pci 0000:00:08.0: PME# disabled
[ 0.236990] pci 0000:00:0a.0: reg 10 32bit mmio: [0xfce7d000-0xfce7dfff]
[ 0.236996] pci 0000:00:0a.0: reg 14 io port: [0xc080-0xc087]
[ 0.237002] pci 0000:00:0a.0: reg 18 32bit mmio: [0xfce7e800-0xfce7e8ff]
[ 0.237008] pci 0000:00:0a.0: reg 1c 32bit mmio: [0xfce7e400-0xfce7e40f]
[ 0.237039] pci 0000:00:0a.0: supports D1 D2
[ 0.237041] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.237046] pci 0000:00:0a.0: PME# disabled
[ 0.237085] pci 0000:00:0b.0: reg 10 io port: [0xc000-0xc007]
[ 0.237091] pci 0000:00:0b.0: reg 14 io port: [0xbc00-0xbc03]
[ 0.237096] pci 0000:00:0b.0: reg 18 io port: [0xb880-0xb887]
[ 0.237102] pci 0000:00:0b.0: reg 1c io port: [0xb800-0xb803]
[ 0.237108] pci 0000:00:0b.0: reg 20 io port: [0xb480-0xb48f]
[ 0.237113] pci 0000:00:0b.0: reg 24 32bit mmio: [0xfce72000-0xfce73fff]
[ 0.237197] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.237201] pci 0000:00:10.0: PME# disabled
[ 0.237414] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.237422] pci 0000:00:15.0: PME# disabled
[ 0.237659] pci 0000:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.237668] pci 0000:00:16.0: PME# disabled
[ 0.237904] pci 0000:00:17.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.237913] pci 0000:00:17.0: PME# disabled
[ 0.238149] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.238158] pci 0000:00:18.0: PME# disabled
[ 0.238254] pci 0000:00:09.0: transparent bridge
[ 0.238299] pci 0000:02:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[ 0.238310] pci 0000:02:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
[ 0.238322] pci 0000:02:00.0: reg 1c 64bit mmio: [0xde000000-0xdfffffff]
[ 0.238329] pci 0000:02:00.0: reg 24 io port: [0xdc00-0xdc7f]
[ 0.238336] pci 0000:02:00.0: reg 30 32bit mmio: [0xfcfe0000-0xfcffffff]
[ 0.238404] pci 0000:00:10.0: bridge io port: [0xd000-0xdfff]
[ 0.238408] pci 0000:00:10.0: bridge 32bit mmio: [0xfcf00000-0xfdffffff]
[ 0.238414] pci 0000:00:10.0: bridge 64bit mmio pref: [0xde000000-0xefffffff]
[ 0.238484] pci 0000:00:15.0: bridge io port: [0xe000-0xefff]
[ 0.238492] pci 0000:00:15.0: bridge 32bit mmio: [0xfe000000-0xfeafffff]
[ 0.238508] pci 0000:00:15.0: bridge 64bit mmio pref: [0xfa000000-0xfbffffff]
[ 0.238572] pci 0000:06:00.0: reg 10 64bit mmio: [0xfebf0000-0xfebfffff]
[ 0.238636] pci 0000:06:00.0: supports D1
[ 0.238638] pci 0000:06:00.0: PME# supported from D0 D1 D3hot
[ 0.238643] pci 0000:06:00.0: PME# disabled
[ 0.238727] pci 0000:00:16.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[ 0.238980] pci_bus 0000:00: on NUMA node 0
[ 0.238988] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.239238] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.239406] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
[ 0.239566] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.239674] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[ 0.239790] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.239897] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.255726] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.256104] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 0.256465] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.256825] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.257183] ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *0, disabled.
[ 0.257543] ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *0, disabled.
[ 0.257900] ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *0, disabled.
[ 0.258256] ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *0, disabled.
[ 0.258613] ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled.
[ 0.258971] ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled.
[ 0.259327] ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled.
[ 0.259682] ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled.
[ 0.260054] ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *0, disabled.
[ 0.260415] ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled.
[ 0.260774] ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled.
[ 0.261133] ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled.
[ 0.261489] ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *0, disabled.
[ 0.261845] ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled.
[ 0.262207] ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled.
[ 0.262565] ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled.
[ 0.262929] ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *10
[ 0.263288] ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled.
[ 0.263648] ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled.
[ 0.264019] ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled.
[ 0.264378] ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *0, disabled.
[ 0.264736] ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled.
[ 0.265093] ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled.
[ 0.265450] ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled.
[ 0.265805] ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled.
[ 0.266165] ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled.
[ 0.266524] ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled.
[ 0.266883] ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled.
[ 0.267248] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10
[ 0.267610] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 0.267969] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *14
[ 0.268341] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *15
[ 0.268705] ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *15
[ 0.269076] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *14
[ 0.269440] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *7
[ 0.269807] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 0.270227] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.270587] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled.
[ 0.270942] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled.
[ 0.271302] ACPI: PCI Interrupt Link [LRP0] (IRQs 20 21 22 23) *0, disabled.
[ 0.271659] ACPI: PCI Interrupt Link [LRP1] (IRQs 20 21 22 23) *0, disabled.
[ 0.272029] ACPI: PCI Interrupt Link [LRP2] (IRQs 20 21 22 23) *0, disabled.
[ 0.272395] ACPI: PCI Interrupt Link [LRP3] (IRQs 20 21 22 23) *10
[ 0.272763] ACPI: PCI Interrupt Link [LRP4] (IRQs 20 21 22 23) *11
[ 0.273131] ACPI: PCI Interrupt Link [LRP5] (IRQs 20 21 22 23) *9
[ 0.273494] ACPI: PCI Interrupt Link [LRP6] (IRQs 20 21 22 23) *5
[ 0.273719] SCSI subsystem initialized
[ 0.273763] libata version 3.00 loaded.
[ 0.273763] usbcore: registered new interface driver usbfs
[ 0.273763] usbcore: registered new interface driver hub
[ 0.273763] usbcore: registered new device driver usb
[ 0.273763] ACPI: WMI: Mapper loaded
[ 0.273763] PCI: Using ACPI for IRQ routing
[ 0.284010] Bluetooth: Core ver 2.15
[ 0.284029] NET: Registered protocol family 31
[ 0.284029] Bluetooth: HCI device and connection manager initialized
[ 0.284029] Bluetooth: HCI socket layer initialized
[ 0.284029] NetLabel: Initializing
[ 0.284029] NetLabel: domain hash size = 128
[ 0.284029] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.284037] NetLabel: unlabeled traffic allowed by default
[ 0.284071] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31, 31
[ 0.284078] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[ 0.300010] pnp: PnP ACPI init
[ 0.300035] ACPI: bus type pnp registered
[ 0.309055] pnp: PnP ACPI: found 14 devices
[ 0.309057] ACPI: ACPI bus type pnp unregistered
[ 0.309062] PnPBIOS: Disabled by ACPI PNP
[ 0.309079] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 0.309082] system 00:04: ioport range 0x800-0x80f has been reserved
[ 0.309085] system 00:04: ioport range 0x4000-0x407f has been reserved
[ 0.309088] system 00:04: ioport range 0x4080-0x40ff has been reserved
[ 0.309090] system 00:04: ioport range 0x4400-0x447f has been reserved
[ 0.309093] system 00:04: ioport range 0x4480-0x44ff has been reserved
[ 0.309096] system 00:04: ioport range 0x4800-0x487f has been reserved
[ 0.309099] system 00:04: ioport range 0x4880-0x48ff has been reserved
[ 0.309103] system 00:04: iomem range 0xfefe2000-0xfefe3fff has been reserved
[ 0.309106] system 00:04: iomem range 0xfefe1000-0xfefe1fff has been reserved
[ 0.309109] system 00:04: iomem range 0xfee01000-0xfeefffff has been reserved
[ 0.309112] system 00:04: iomem range 0xfed01000-0xfed01fff has been reserved
[ 0.309123] system 00:07: ioport range 0x250-0x253 has been reserved
[ 0.309126] system 00:07: ioport range 0x256-0x25f has been reserved
[ 0.309129] system 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.309132] system 00:07: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.309139] system 00:0a: ioport range 0xa00-0xa0f has been reserved
[ 0.309144] system 00:0b: ioport range 0x5000-0x507f has been reserved
[ 0.309147] system 00:0b: ioport range 0x5080-0x50ff has been reserved
[ 0.309153] system 00:0c: iomem range 0xf0000000-0xf1ffffff has been reserved
[ 0.309159] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 0.309162] system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
[ 0.309165] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 0.309168] system 00:0d: iomem range 0x100000-0xbfffffff could not be reserved
[ 0.309171] system 00:0d: iomem range 0xf0000000-0xffffffff could not be reserved
[ 0.343853] AppArmor: AppArmor Filesystem Enabled
[ 0.343965] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[ 0.343967] pci 0000:00:09.0: IO window: disabled
[ 0.343972] pci 0000:00:09.0: MEM window: disabled
[ 0.343976] pci 0000:00:09.0: PREFETCH window: disabled
[ 0.343980] pci 0000:00:10.0: PCI bridge, secondary bus 0000:02
[ 0.343993] pci 0000:00:10.0: IO window: 0xd000-0xdfff
[ 0.343998] pci 0000:00:10.0: MEM window: 0xfcf00000-0xfdffffff
[ 0.344002] pci 0000:00:10.0: PREFETCH window: 0x000000de000000-0x000000efffffff
[ 0.344007] pci 0000:00:15.0: PCI bridge, secondary bus 0000:03
[ 0.344013] pci 0000:00:15.0: IO window: 0xe000-0xefff
[ 0.344024] pci 0000:00:15.0: MEM window: 0xfe000000-0xfeafffff
[ 0.344032] pci 0000:00:15.0: PREFETCH window: 0x000000fa000000-0x000000fbffffff
[ 0.344046] pci 0000:00:16.0: PCI bridge, secondary bus 0000:06
[ 0.344048] pci 0000:00:16.0: IO window: disabled
[ 0.344059] pci 0000:00:16.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.344067] pci 0000:00:16.0: PREFETCH window: disabled
[ 0.344075] pci 0000:00:17.0: PCI bridge, secondary bus 0000:07
[ 0.344077] pci 0000:00:17.0: IO window: disabled
[ 0.344088] pci 0000:00:17.0: MEM window: disabled
[ 0.344096] pci 0000:00:17.0: PREFETCH window: disabled
[ 0.344104] pci 0000:00:18.0: PCI bridge, secondary bus 0000:08
[ 0.344106] pci 0000:00:18.0: IO window: disabled
[ 0.344116] pci 0000:00:18.0: MEM window: disabled
[ 0.344124] pci 0000:00:18.0: PREFETCH window: disabled
[ 0.344140] pci 0000:00:09.0: setting latency timer to 64
[ 0.344148] pci 0000:00:10.0: setting latency timer to 64
[ 0.344665] ACPI: PCI Interrupt Link [LRP3] enabled at IRQ 23
[ 0.344670] alloc irq_desc for 23 on node -1
[ 0.344672] alloc kstat_irqs on node -1
[ 0.344679] pci 0000:00:15.0: PCI INT A -> Link[LRP3] -> GSI 23 (level, low) -> IRQ 23
[ 0.344688] pci 0000:00:15.0: setting latency timer to 64
[ 0.345182] ACPI: PCI Interrupt Link [LRP4] enabled at IRQ 22
[ 0.345186] alloc irq_desc for 22 on node -1
[ 0.345188] alloc kstat_irqs on node -1
[ 0.345192] pci 0000:00:16.0: PCI INT A -> Link[LRP4] -> GSI 22 (level, low) -> IRQ 22
[ 0.345202] pci 0000:00:16.0: setting latency timer to 64
[ 0.345696] ACPI: PCI Interrupt Link [LRP5] enabled at IRQ 21
[ 0.345699] alloc irq_desc for 21 on node -1
[ 0.345701] alloc kstat_irqs on node -1
[ 0.345705] pci 0000:00:17.0: PCI INT A -> Link[LRP5] -> GSI 21 (level, low) -> IRQ 21
[ 0.345714] pci 0000:00:17.0: setting latency timer to 64
[ 0.346206] ACPI: PCI Interrupt Link [LRP6] enabled at IRQ 20
[ 0.346209] alloc irq_desc for 20 on node -1
[ 0.346211] alloc kstat_irqs on node -1
[ 0.346215] pci 0000:00:18.0: PCI INT A -> Link[LRP6] -> GSI 20 (level, low) -> IRQ 20
[ 0.346224] pci 0000:00:18.0: setting latency timer to 64
[ 0.346231] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.346234] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.346237] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
[ 0.346239] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
[ 0.346242] pci_bus 0000:02: resource 0 io: [0xd000-0xdfff]
[ 0.346244] pci_bus 0000:02: resource 1 mem: [0xfcf00000-0xfdffffff]
[ 0.346247] pci_bus 0000:02: resource 2 pref mem [0xde000000-0xefffffff]
[ 0.346250] pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
[ 0.346252] pci_bus 0000:03: resource 1 mem: [0xfe000000-0xfeafffff]
[ 0.346255] pci_bus 0000:03: resource 2 pref mem [0xfa000000-0xfbffffff]
[ 0.346258] pci_bus 0000:06: resource 1 mem: [0xfeb00000-0xfebfffff]
[ 0.346299] NET: Registered protocol family 2
[ 0.346404] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.346749] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.347334] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.347731] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.347735] TCP reno registered
[ 0.347878] NET: Registered protocol family 1
[ 0.347960] Trying to unpack rootfs image as initramfs...
[ 0.501797] Switched to high resolution mode on CPU 1
[ 0.503978] Switched to high resolution mode on CPU 0
[ 0.539918] Freeing initrd memory: 7474k freed
[ 0.544983] Simple Boot Flag value 0x20 read from CMOS RAM was invalid
[ 0.544988] Simple Boot Flag at 0xff set to 0x1
[ 0.545189] cpufreq-nforce2: No nForce2 chipset.
[ 0.545220] Scanning for low memory corruption every 60 seconds
[ 0.545345] audit: initializing netlink socket (disabled)
[ 0.545366] type=2000 audit(1272220986.544:1): initialized
[ 0.554144] highmem bounce pool size: 64 pages
[ 0.554150] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.555641] VFS: Disk quotas dquot_6.5.2
[ 0.555704] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.556260] fuse init (API version 7.12)
[ 0.556345] msgmni has been set to 1686
[ 0.556561] alg: No test for stdrng (krng)
[ 0.556576] io scheduler noop registered
[ 0.556578] io scheduler anticipatory registered
[ 0.556581] io scheduler deadline registered
[ 0.556625] io scheduler cfq registered (default)
[ 0.572198] pci 0000:02:00.0: Boot video device
[ 0.572510] alloc irq_desc for 24 on node -1
[ 0.572513] alloc kstat_irqs on node -1
[ 0.572535] pcieport-driver 0000:00:15.0: irq 24 for MSI/MSI-X
[ 0.572558] pcieport-driver 0000:00:15.0: setting latency timer to 64
[ 0.572936] alloc irq_desc for 25 on node -1
[ 0.572938] alloc kstat_irqs on node -1
[ 0.572956] pcieport-driver 0000:00:16.0: irq 25 for MSI/MSI-X
[ 0.572977] pcieport-driver 0000:00:16.0: setting latency timer to 64
[ 0.573352] alloc irq_desc for 26 on node -1
[ 0.573354] alloc kstat_irqs on node -1
[ 0.573372] pcieport-driver 0000:00:17.0: irq 26 for MSI/MSI-X
[ 0.573393] pcieport-driver 0000:00:17.0: setting latency timer to 64
[ 0.573767] alloc irq_desc for 27 on node -1
[ 0.573769] alloc kstat_irqs on node -1
[ 0.573787] pcieport-driver 0000:00:18.0: irq 27 for MSI/MSI-X
[ 0.573808] pcieport-driver 0000:00:18.0: setting latency timer to 64
[ 0.573982] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.574008] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.574284] ACPI: AC Adapter [AC0] (on-line)
[ 0.574364] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.574368] ACPI: Power Button [PWRF]
[ 0.574446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.574453] ACPI: Power Button [PWRB]
[ 0.574502] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 0.574508] ACPI: Sleep Button [SLPB]
[ 0.574550] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 0.574820] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.582164] ACPI: Lid Switch [LID]
[ 0.583155] ACPI: SSDT affae620 00248 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.584066] ACPI: SSDT affae900 00765 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.585401] Monitor-Mwait will be used to enter C-1 state
[ 0.585432] Monitor-Mwait will be used to enter C-2 state
[ 0.585456] Monitor-Mwait will be used to enter C-3 state
[ 0.585464] Marking TSC unstable due to TSC halts in idle
[ 0.585487] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 0.585517] processor LNXCPU:00: registered as cooling_device0
[ 0.585521] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.585935] ACPI: SSDT affae550 000CC (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.586528] ACPI: SSDT affae870 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.588006] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 0.588034] processor LNXCPU:01: registered as cooling_device1
[ 0.588038] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.602303] ACPI Warning: \_TZ_.THRM._PSL: Return Package type mismatch at index 0 - found Processor, expected Reference 20090521 nspredef-946
[ 0.602312] ACPI: Expecting a [Reference] package element, found type C
[ 0.602315] ACPI: Invalid passive threshold
[ 0.603135] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.603143] ACPI: Thermal Zone [THRM] (78 C)
[ 0.603222] isapnp: Scanning for PnP cards...
[ 0.747185] ACPI: Battery Slot [BAT0] (battery present)
[ 0.959036] isapnp: No Plug & Play device found
[ 0.960455] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.961866] brd: module loaded
[ 0.962328] loop: module loaded
[ 0.962410] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.962489] ahci 0000:00:0b.0: version 3.0
[ 0.963015] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 0.963021] ahci 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[ 0.963063] alloc irq_desc for 28 on node -1
[ 0.963066] alloc kstat_irqs on node -1
[ 0.963077] ahci 0000:00:0b.0: irq 28 for MSI/MSI-X
[ 0.963122] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 0.963125] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pmp pio slum part
[ 0.963130] ahci 0000:00:0b.0: setting latency timer to 64
[ 0.963356] scsi0 : ahci
[ 0.963481] scsi1 : ahci
[ 0.963567] ata1: SATA max UDMA/133 abar m8192@0xfce72000 port 0xfce72100 irq 28
[ 0.963570] ata2: SATA max UDMA/133 abar m8192@0xfce72000 port 0xfce72180 irq 28
[ 0.964525] Fixed MDIO Bus: probed
[ 0.964560] PPP generic driver version 2.4.2
[ 0.964833] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.965380] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[ 0.965385] ehci_hcd 0000:00:04.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.965404] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 0.965408] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 0.965449] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 0.965477] ehci_hcd 0000:00:04.1: debug port 1
[ 0.965483] ehci_hcd 0000:00:04.1: cache line size of 32 is not supported
[ 0.965500] ehci_hcd 0000:00:04.1: irq 22, io mem 0xfce7ec00
[ 0.976019] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 0.976108] usb usb1: configuration #1 chosen from 1 choice
[ 0.976138] hub 1-0:1.0: USB hub found
[ 0.976147] hub 1-0:1.0: 8 ports detected
[ 0.976209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.976734] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
[ 0.976739] ohci_hcd 0000:00:04.0: PCI INT A -> Link[LUB0] -> GSI 21 (level, low) -> IRQ 21
[ 0.976753] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 0.976756] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 0.976794] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 0.976819] ohci_hcd 0000:00:04.0: irq 21, io mem 0xfce7f000
[ 1.034066] usb usb2: configuration #1 chosen from 1 choice
[ 1.034094] hub 2-0:1.0: USB hub found
[ 1.034102] hub 2-0:1.0: 8 ports detected
[ 1.034157] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.034254] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.036976] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.039056] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.039062] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.039065] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.039068] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.039071] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.039139] mice: PS/2 mouse device common for all mice
[ 1.039284] rtc_cmos 00:06: RTC can wake from S4
[ 1.039317] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.039367] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 1.039469] device-mapper: uevent: version 1.0.3
[ 1.039574] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.039666] device-mapper: multipath: version 1.1.0 loaded
[ 1.039669] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.039794] EISA: Probing bus 0 at eisa.0
[ 1.039807] Cannot allocate resource for EISA slot 4
[ 1.039810] Cannot allocate resource for EISA slot 5
[ 1.039820] EISA: Detected 0 cards.
[ 1.040013] cpuidle: using governor ladder
[ 1.040138] cpuidle: using governor menu
[ 1.040650] TCP cubic registered
[ 1.040806] NET: Registered protocol family 10
[ 1.041282] lo: Disabled Privacy Extensions
[ 1.041627] NET: Registered protocol family 17
[ 1.041649] Bluetooth: L2CAP ver 2.13
[ 1.041650] Bluetooth: L2CAP socket layer initialized
[ 1.041653] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.041655] Bluetooth: SCO socket layer initialized
[ 1.041699] Bluetooth: RFCOMM TTY layer initialized
[ 1.041703] Bluetooth: RFCOMM socket layer initialized
[ 1.041704] Bluetooth: RFCOMM ver 1.11
[ 1.042912] Using IPI No-Shortcut mode
[ 1.042982] PM: Resume from disk failed.
[ 1.042995] registered taskstats version 1
[ 1.043116] Magic number: 6:460:747
[ 1.043260] rtc_cmos 00:06: setting system clock to 2010-04-25 18:43:08 UTC (1272220988)
[ 1.043263] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.043265] EDD information not available.
[ 1.077239] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.289046] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 1.423461] usb 1-3: configuration #1 chosen from 1 choice
[ 1.444083] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.445284] ata1.00: ATA-8: ST9160310AS, 0303, max UDMA/133
[ 1.445288] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.446750] ata1.00: configured for UDMA/133
[ 1.446889] scsi 0:0:0:0: Direct-Access ATA ST9160310AS 0303 PQ: 0 ANSI: 5
[ 1.447013] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.447053] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.447099] sd 0:0:0:0: [sda] Write Protect is off
[ 1.447102] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.447125] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.447259] sda:
[ 1.449053] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.464209] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633A, AS00, max UDMA/100, ATAPI AN
[ 1.464224] ata2.00: applying bridge limits
[ 1.478022] ata2.00: configured for UDMA/100
[ 1.479713] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x7 t4
[ 1.479715] ata2: irq_stat 0x40000001
[ 1.479720] ata2: hard resetting link
[ 1.500020] Clocksource tsc unstable (delta = -146311752 ns)
[ 1.588032] usb 1-7: new high speed USB device using ehci_hcd and address 4
[ 1.684132] sda1 sda2 <
[ 1.734217] usb 1-7: configuration #1 chosen from 1 choice
[ 1.737664] sda5 >
[ 1.737932] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.960033] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.988427] ata2.00: configured for UDMA/100
[ 1.989044] ata2: EH complete
[ 1.991644] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633A AS00 PQ: 0 ANSI: 5
[ 1.997712] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.997716] Uniform CD-ROM driver Revision: 3.20
[ 1.997796] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.997842] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.997875] Freeing unused kernel memory: 540k freed
[ 1.998246] Write protecting the kernel text: 4580k
[ 1.998303] Write protecting the kernel read-only data: 1840k
[ 2.040047] usb 2-4: new low speed USB device using ohci_hcd and address 2
[ 2.201282] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 2.201927] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 2.201935] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 2.201942] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 2.232415] acpi device:1a: registered as cooling_device2
[ 2.232596] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:11/device:12/input/input6
[ 2.232644] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.248209] Initializing USB Mass Storage driver...
[ 2.248578] scsi2 : SCSI emulation for USB Mass Storage devices
[ 2.249589] usbcore: registered new interface driver usb-storage
[ 2.249593] USB Mass Storage support registered.
[ 2.249755] usb-storage: device found at 2
[ 2.249757] usb-storage: waiting for device to settle before scanning
[ 2.275123] usb 2-4: configuration #1 chosen from 1 choice
[ 2.283347] usbcore: registered new interface driver hiddev
[ 2.289294] input: Logitech USB-PS/2 Trackball as /devices/pci0000:00/0000:00:04.0/usb2/2-4/2-4:1.0/input/input7
[ 2.289379] generic-usb 0003:046D:C401.0001: input,hidraw0: USB HID v1.00 Mouse [Logitech USB-PS/2 Trackball] on usb-0000:00:04.0-4/input0
[ 2.289396] usbcore: registered new interface driver usbhid
[ 2.289399] usbhid: v2.6:USB HID core driver
[ 2.721271] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:23:54:84:15:0e
[ 2.721276] forcedeth 0000:00:0a.0: highdma csum pwrctl gbit lnktim msi desc-v3
[ 3.932641] PM: Starting manual resume from disk
[ 3.932645] PM: Resume from partition 8:5
[ 3.932648] PM: Checking hibernation image.
[ 3.932901] PM: Resume from disk failed.
[ 4.002967] EXT4-fs (sda1): barriers enabled
[ 4.038406] kjournald2 starting: pid 406, dev sda1:8, commit interval 5 seconds
[ 4.038465] EXT4-fs (sda1): delayed allocation enabled
[ 4.038469] EXT4-fs: file extents enabled
[ 4.042785] EXT4-fs: mballoc enabled
[ 4.042802] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 4.889423] type=1505 audit(1272220992.344:2): operation="profile_load" pid=431 name=/sbin/dhclient3
[ 4.890170] type=1505 audit(1272220992.344:3): operation="profile_load" pid=431 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 4.890567] type=1505 audit(1272220992.344:4): operation="profile_load" pid=431 name=/usr/lib/connman/scripts/dhclient-script
[ 4.963245] type=1505 audit(1272220992.416:5): operation="profile_load" pid=433 name=/usr/lib/cups/backend/cups-pdf
[ 4.964140] type=1505 audit(1272220992.420:6): operation="profile_load" pid=433 name=/usr/sbin/cupsd
[ 4.967391] type=1505 audit(1272220992.420:7): operation="profile_load" pid=434 name=/usr/sbin/mysqld-akonadi
[ 4.971408] type=1505 audit(1272220992.424:8): operation="profile_load" pid=435 name=/usr/sbin/tcpdump
[ 7.248362] usb-storage: device scan complete
[ 7.249815] scsi 2:0:0:0: Direct-Access Kingston DataTraveler G2 1.00 PQ: 0 ANSI: 2
[ 7.250334] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.251295] sd 2:0:0:0: [sdb] 7818240 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 7.252669] sd 2:0:0:0: [sdb] Write Protect is off
[ 7.252672] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 7.252674] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.255666] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.255669] sdb:
[ 7.258668] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 7.258671] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 15.171040] udev: starting version 147
[ 15.184042] lp: driver loaded but no devices found
[ 15.198058] asus_laptop: Asus Laptop Support version 0.42
[ 15.207014] asus_laptop: BSTS called, 0xff4f returned
[ 15.207077] asus_laptop: F5GL model detected
[ 15.208132] input: Asus Laptop extra buttons as /devices/virtual/input/input8
[ 15.208248] Registered led device: asus::mail
[ 15.208324] asus_laptop: Brightness ignored, must be controlled by ACPI video driver
[ 15.237633] Adding 6385796k swap on /dev/sda5. Priority:-1 extents:1 across:6385796k
[ 15.257854] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.283157] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4d00
[ 15.283164] ACPI: I/O resource nForce2_smbus [0x4e00-0x4e3f] conflicts with ACPI region SM00 [0x4e00-0x4e3f]
[ 15.283167] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 15.283170] nForce2_smbus 0000:00:03.2: Error probing SMB2.
[ 15.436261] Linux agpgart interface v0.103
[ 15.437065] cfg80211: Calling CRDA to update world regulatory domain
[ 15.453509] EXT4-fs (sda1): internal journal on sda1:8
[ 15.470768] cfg80211: World regulatory domain updated:
[ 15.470784] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.470787] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.470790] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.470793] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.470795] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.470798] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.484173] nvidia: module license 'NVIDIA' taints kernel.
[ 15.484179] Disabling lock debugging due to kernel taint
[ 15.732867] ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 19
[ 15.732874] alloc irq_desc for 19 on node -1
[ 15.732877] alloc kstat_irqs on node -1
[ 15.732886] ath9k 0000:06:00.0: PCI INT A -> Link[LN4A] -> GSI 19 (level, low) -> IRQ 19
[ 15.732896] ath9k 0000:06:00.0: setting latency timer to 64
[ 15.747406] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 23
[ 15.747411] nvidia 0000:02:00.0: PCI INT A -> Link[SGRU] -> GSI 23 (level, low) -> IRQ 23
[ 15.747418] nvidia 0000:02:00.0: setting latency timer to 64
[ 15.747603] NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.36 Fri Aug 14 17:18:04 PDT 2009
[ 15.899439] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.908854] Linux video capture interface: v2.00
[ 15.911835] uvcvideo: Found UVC 1.00 device USB2.0 1.3M UVC WebCam (04f2:b012)
[ 15.938678] input: USB2.0 1.3M UVC WebCam as /devices/pci0000:00/0000:00:04.1/usb1/1-7/1-7:1.0/input/input9
[ 15.938733] usbcore: registered new interface driver uvcvideo
[ 15.938736] USB Video Class driver (v0.1.0)
[ 15.955975] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 15.956497] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 15.956503] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[ 15.956535] HDA Intel 0000:00:08.0: setting latency timer to 64
[ 16.160479] ath: EEPROM regdomain: 0x60
[ 16.160482] ath: EEPROM indicates we should expect a direct regpair map
[ 16.160486] ath: Country alpha2 being used: 00
[ 16.160488] ath: Regpair used: 0x60
[ 16.171104] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 16.171872] Registered led device: ath9k-phy0::radio
[ 16.171890] Registered led device: ath9k-phy0::assoc
[ 16.171909] Registered led device: ath9k-phy0::tx
[ 16.171925] Registered led device: ath9k-phy0::rx
[ 16.171950] phy0: Atheros AR9280 MAC/BB Rev:2 AR5133 RF Rev:d0: mem=0xf80a0000, irq=19
[ 16.522226] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:08.0/input/input10
[ 16.605283] Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
[ 16.643648] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input11
[ 17.167966] type=1505 audit(1272221004.621:9): operation="profile_replace" pid=977 name=/sbin/dhclient3
[ 17.168704] type=1505 audit(1272221004.621:10): operation="profile_replace" pid=977 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 17.169174] type=1505 audit(1272221004.625:11): operation="profile_replace" pid=977 name=/usr/lib/connman/scripts/dhclient-script
[ 17.173374] type=1505 audit(1272221004.629:12): operation="profile_replace" pid=979 name=/usr/lib/cups/backend/cups-pdf
[ 17.174235] type=1505 audit(1272221004.629:13): operation="profile_replace" pid=979 name=/usr/sbin/cupsd
[ 17.177105] type=1505 audit(1272221004.633:14): operation="profile_replace" pid=980 name=/usr/sbin/mysqld-akonadi
[ 17.179282] type=1505 audit(1272221004.633:15): operation="profile_replace" pid=981 name=/usr/sbin/tcpdump
[ 17.418693] alloc irq_desc for 29 on node -1
[ 17.418698] alloc kstat_irqs on node -1
[ 17.418711] forcedeth 0000:00:0a.0: irq 29 for MSI/MSI-X
[ 17.418914] eth0: no link during initialization.
[ 17.419401] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.482415] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.366737] ppdev: user-space parallel port driver
[ 45.071045] wlan0: authenticate with AP 00:1d:73:b3:60:38
[ 45.073619] wlan0: authenticated
[ 45.073623] wlan0: associate with AP 00:1d:73:b3:60:38
[ 45.079411] wlan0: RX AssocResp from 00:1d:73:b3:60:38 (capab=0x431 status=0 aid=2)
[ 45.079416] wlan0: associated
[ 45.088773] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 45.178274] padlock: VIA PadLock not detected.
[ 55.372035] wlan0: no IPv6 routers present

and here's some logs from my router;

2010/04/25 19:48:33 AUTH wl0: AUTH: PSK authentication successful: 00:22:43:51:b9:4b
2010/04/25 19:48:33 AUTH ath0: STA 00:22:43:51:b9:4b WPA: pairwise key handshake completed (RSN)
2010/04/25 19:48:33 WIRELESS ath0: had associated successfully : 00:22:43:51:b9:4b
2010/04/25 19:48:33 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: associated
2010/04/25 19:48:32 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: deassociated
2010/04/25 19:48:32 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: deauthenticated due to local deauth request
2010/04/25 19:48:29 WIRELESS ath0: had associated successfully : 00:22:43:51:b9:4b
2010/04/25 19:48:29 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: associated
2010/04/25 19:45:40 AUTH ath0: STA 00:23:76:07:c9:34 IEEE 802.11: deassociated
2010/04/25 19:43:53 DHCPS sending ACK to 192.168.11.2
2010/04/25 19:43:53 DHCPS Request incoming from dante-laptop(len:12)
2010/04/25 19:43:51 AUTH wl0: AUTH: PSK authentication successful: 00:22:43:51:b9:4b
2010/04/25 19:43:51 AUTH ath0: STA 00:22:43:51:b9:4b WPA: pairwise key handshake completed (RSN)
2010/04/25 19:43:51 WIRELESS ath0: had associated successfully : 00:22:43:51:b9:4b
2010/04/25 19:43:51 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: associated
2010/04/25 19:34:41 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: deassociated
2010/04/25 19:31:25 DHCPS sending ACK to 192.168.11.2
2010/04/25 19:31:25 DHCPS Request incoming from dante-laptop(len:12)
2010/04/25 19:31:22 AUTH wl0: AUTH: PSK authentication successful: 00:22:43:51:b9:4b
2010/04/25 19:31:22 AUTH ath0: STA 00:22:43:51:b9:4b WPA: pairwise key handshake completed (RSN)
2010/04/25 19:31:22 WIRELESS ath0: had associated successfully : 00:22:43:51:b9:4b
2010/04/25 19:31:22 AUTH ath0: STA 00:22:43:51:b9:4b IEEE 802.11: associated
2010/04/25 19:26:29 DHCPS sending ACK to 192.168.11.6
2010/04/25 19:26:24 DHCPS sending OFFER of 192.168.11.6

Looks like your computer disconnects before your router has the chance to respond to the DHCP acknowledgement...

Have you tried setting a static IP address?

I'm not sure how to do it here...I do know how to do it on Windows, though...

Assuming you use KNetworkManager... Tray Icon > Manage Connections > (Select Connection) > Edit > IP address.

Change method to "Manual" then enter the details needed. Confirm and connect to the network.